Estimasi Kebutuhan Material Cat Pada Bottom dan Lambung Kapal Tongkang 300 Feet
Improvements in terms of protection against corrosion are carried out regularly in the shipping industry. One alternative that is used is painting or coating. Painting is a method to prevent the plate from corroding. Coating is a stage that must be passed in the ship repair and construction process. In the ship repair process, material needs are importhant things that must be planned. The paint or coating material used in this study is paint according to specifications for the shipping industry. The purpose of this study was to obtain the required cat consumption based on surface area reference. The ship repair and construction process includes coating or painting work. The need for paint is based on the surface area of the underwater, bottom and topside of the 300 feet barge that will be painted. This research is a quantitative research where the final result is in the form of numbers. Results of calculating the area of the ship: a. Flat bottom painting of 1926.06 m2; b. Painting the lower vertical area of 22.32 m2; c. Painting the lower area of 717.82 m2 and d. Painting of the topside area of 296.5 m2. The calculation of the cat's needs is that the underground (flat and vertical bottom) is 1717.96 liters and the bottomtop and topside are 738.24 liters. The research conclusions obtained were that the smallest volume of cat used in underwater painting was 1717.96 liters and in the bottom - topside area was 738.24 liters and the surface area under water (flat bottom and vertical bottom) was 2150.38 m2 (~2150 m2) and the bottom-topside area is 1014.32 m2 (~1014 m2).
L. Benea, N. Simionescu, and L. Mardare, “The effect of polymeric protective layers and the immersion time on the corrosion behavior of naval steel in natural seawater,” J. Mater. Res. Technol., vol. 9, no. 6, pp. 13174–13184, 2020, doi: 10.1016/j.jmrt.2020.09.059.
H. Herdiyana and M. , AsepRachmat, ST., “Proses Perawatan Badan Kapal Terhadap Korosi Dengan menggunakan Metode Coating,” Semnastekmu, vol. 1, no. 1, pp. 147–153, 2021.
W. D. Kurniawan and P. Periyanto, “Proses Sandblasting dan Coating Pada Kapal di PT. Dok Perkapalan Surabaya,” Otopro, vol. 13, no. 2, p. 44, 2019, doi: 10.26740/otopro.v13n2.p44-53.
Y. Okumoto, Y. Takeda, M. Mano, and T. Okada, Design of ship hull structures: A practical guide for engineers. 2009. doi: 10.1007/978-3-540-88445-3.
A. Windyandari, A. F. Zakki, and Sarwoko, “Studi Perbandingan Metode Pelapisan (coating) Pada Ruang Muat Berbasis Regulasi IMO,” Teknik, vol. 34, no. 3, pp. 174–181, 2013.
P. H. Setyarini and E. Sulistyo, “Optimasi Proses Sand Blasting Terhadap Laju Korosi Hasil Pengecatan Baja Aisi 430,” J. Rekayasa Mesin, vol. 2, no. 2, pp. 106–109, 2011.
D. Dwilaksana and G. Jatisukamto, “Surface Roughness Analysis of Sand Blasting Process with Variation of Pressure, Time, and Angle using Taguchi Method,” J-Proteksion, vol. 2, no. 1, pp. 27–30, 2017.
S. Khorasanizadeh, “The effects of shot and grit blasting process parameters on steel pipes coating adhesion,” World Acad. Sci. Eng. Technol., vol. 42, no. 6, pp. 1290–1298, 2010.
L. Budiyanto, “Pengaruh Salinitas Air Laut Terhadap Laju Korosi Pada Plat Lambung Kapal Bobot 1500 DWT,” Din. Bahari, vol. 2, no. 1, pp. 91–96, 2021, doi: 10.46484/db.v2i1.256.
H. Risqullah and I. Dirja, “Proses Sandblasting Dalam Proses Fabrikasi Baja Struktur Pada Proyek Refinery Development Master Plan (RDMP) di PT AJP,” J. Ilm. Wahana Pendidik., vol. 8, no. 15, pp. 264–275, 2022, [Online]. Available: https://doi.org/10.5281/zenodo.7049222
R. Zulrian Aldio, Dedikarni, B. Saputra, I. Anwar, and M. S. Masdar, “Pengaruh Penyemprotan Dan Ukuran Mesh Terhadap Kekasaran Permukaan Pada Proses Sandblasting Baja SS400,” J. Renew. Energy Mech., vol. 04, no. 02, pp. 63–75, 2021, doi: 10.25299/rem.2021.vol4(02).7500.
Z. Ariany, “Kajian Reparasi Pengecatan Pada Lambung Kapal (studi Kasus KM. Kirana 3),” vol. 35, no. 1, pp. 27–32, 2014.